|
KTV804
compatible LCD display general 9 inch for CNCmachine replace old RGB MDA EGA
CGA industrial CRT monitor
This
productis used to replace a variety of CNC machine set old RGB, MDA, EGA,
CGAindustrial CRT monitors, wide compatibility, good effect.
Size
8.4-inch LCD, commonly known as 9-inch display.
KTV804 RGB, MDA, EGA, CGA special industrialmonitors
1,supports the 15k to 48k line frequency signal,unrestricted field frequency
input, automatic identification line fieldfrequency input.
2,supports digital RGB, RGB analog and color,monochrome, black and white,
grayscale and other video formats.
3,Supports both interlaced and progressivescanning modes.
4,Support for vertical resolution from 160 linesto 600 lines, automatic
identification.
5,Support any level of resolution, automaticidentification.
6,synchronizing signal separating support, thecomposite synchronization
signal or the composite synchronizing signal on avideo signal, automatic
identification.
7, the output signal of the standard 800 x 600VGA 60Hz field frequency or
custom resolutions.
8, the input impedance of 75 ohms or 750 ohmsoffer two options, you can adapt
weak signal equipment.
|
Model
|
KTV804 RGB EGA CGA MDA
display
|
|
|
display size
|
174*131mm 8.4" 4：3
|
|
|
H&V scanning range
|
scan line
signal:15Khz-48Khz positiveand negative automatic adaptation
|
|
|
Field scan
signal:48hz-75hz positiveand negative automatic adaptation
|
|
|
Input signal
|
Signal type
|
MDA、CGA、EGA、VGA
RGB、RGsB、RGBS、RGBHV
|
|
|
|
Synchronous mode
|
HV line field separate,HV
line fieldblending Cs,Green sync Sog
|
|
|
TTL digital level 2.4-5.0V
or Low 0-0.8V
|
|
|
Analog level 0.7-2.5VP-P
|
|
|
Input impedance
|
75-500 ohm high input
impedance,automatically adapt to a variety of strong and weak signal
source.
|
|
|
Scanning mode
|
Interlaced scan /
progressive scan
|
|
|
The signal line
|
9 pin or 15 pin
|
|
|
Display color
|
262K, monochrome, black
and white
|
|
|
contrast ratio
|
450:1
|
|
|
Brightness
|
400 cd/m2
|
|
|
work environment
|
Temperature:
-10-+65,humidity: 20%-95%
|
|
|
Installation size
|
Including installation of
border240*150*50mm
|
|
|
power adapter
|
External AC100V/240V to
DC12V power,power: 18W,
Optional DC 24V power supply
|
|
The
interface of the display
1. VIDEO IN:
used to connect the 15 pin Dsignal line or the 9 pin D signal line
input.(choose one only)
2. DC 12V:
display power input, used toconnect the power adapter.(can choose 24VDC)
15 pin
connector
If you
choose 9pin connector
If you don’t
know it it’s matching yourrequirement, please send me details about your
monitor. Theengineer will advise.
|
![general 9\" LCD display for CNC replace RGB MDA EGA CGA industrial CRT monitor](images/s/66_1.jpg "general 9\\" LCD display for CNC replace RGB MDA EGA CGA industrial CRT monitor")
![general 9\" LCD display for CNC replace RGB MDA EGA CGA industrial CRT monitor](images/s/66_2.jpg "general 9\\" LCD display for CNC replace RGB MDA EGA CGA industrial CRT monitor")
